Noble

BoilersBoilersWater heater

Lochinvar, LLC releases the NOBLE™ Fire Tube Combi Boiler for residential applications. With three models ranging from 110,000 to 199,999 Btu/hr., the Noble boiler offers easy installation and serviceability, true instantaneous response time and a user-friendly interface. In addition to 10:1 turndown and 95 percent Annual Fuel Utilization Efficiency (AFUE), the Noble Fire Tube Combi Boiler is designed, engineered and assembled in the USA. 

SEE SUPPLIER PAGE

XR3 Series Fittings

Piping

XR3 fittings are designed with a patented feature that when used with FlashShield CSST, contours the metal shield. This creates electrical continuity throughout the system. The XR3 fitting requires minimal torque for easy fitting installation. With no o-rings or gaskets, the reusable brass components provide a reliable metal-to-metal seat
 
• Straight Fittings connect the flexible gas tubing to gas supply, distribution manifolds or gas appliances.
• Couplings allow for the splicing and additions to the flexible gas tubing.
• Tee Fittings create a branch line on tubing runs.
• Termination Fittings create a fixed point “stub-out” on a wall or floor surface.
• Termination Bracket Fittings provide a secure attachment point for key-valves and as an alternate termination point.

Technical data sheet

Gastite® System Corrugated Stainless Steel Tubing (CSST)

Piping

Gastite® Corrugated Stainless Steel Tubing (CSST) supplies natural gas or LP gas to appliances. Gastite is a reliable, cost-effective system that can be installed in all modes of construction. Flexibility means quick and easy installations: Gastite® installs 30-70% faster than traditional piping methods.

• CSST flexible gas piping supplies natural gas or liquefied petroleum gas to appliances.

technical data sheet

WAV-0100

Control systems

Introducing the new HBX Wireless Outdoor Sensor, the WAV-0100. This wireless outdoor sensor goes against all conventional wireless technology. While others communicate only with their own devices, HBX has developed a way to broaden horizons. The WAV-0100 is able to connect to any control that uses a thermistor input for its outdoor sensing. Because of this revolutionary technology, the WAV-0100 can connect to boilers, reset controls, thermostats and many other devices. This makes the WAV-0100 perfect for retrofits as well as new installs.

CPU-0550 

Control systems

Introducing the simplest, most intuitive control available to the hydronic industry, the CPU-0550. The unique design means minutes to learn, minutes to setup. This control covers a wide variety of applications from a single unit, reducing the number of different controls on your shelf.

The CPU-0550 stand alone outdoor reset control accommodates staging, mixing, differential setpoint and pump sequencer applications in a condensed package with extensive flexibility.

Technical sheet

ORC-0100 

Control systems

The HBX ORC-0100 is designed to be an energy-saving automatic control for hot water boilers. The ORC-0100 measures the outside air temperature and re-adjust the heating system water to a minimum water temperature to satisfy the heat loss of the home or building.

THM-0100

Control systems

This diverse single stage heating/cooling THM-0100 Non-Programmable Thermostat is also designed around PID Algorithm theory and can also benefit applications requiring a single setpoint control. A single on board auxiliary sensor will allow for internal room, external floor, or outdoor sensing options.

SNO-0550

Control systems

Introducing the simplest, most intuitive control available to the industry, The SN0-0550 . This standalone snow melt control replaces the SNO-0500 at the same competitive price as the previous control, but with more features and benefits. This unique control uses a new step-by-step interface allowing for easy set up. With new preset snow conditions (Very Light, Light, Moderate and Heavy), it is simple to set the control to turn on the system based on snowfall intensity.

The new snow melt control utilizes the HBX Optical Snow Sensor (SNO-0110). This snow/ice sensor utilizes optics rather than continuity based on/off sensors typically used by other manufacturers. The sensor provides HBX snow melt controls with feedback on snowfall rate and Slab Temperature.

Concentric

Chimneys

Material & Construction

InnoFlue® Concentric integrates our industry leading InnoFlue® Single Wall, flame retardant, polypropylene technology and white powder coated metal outers. This integrated system allows both flue gases and fresh air to flow through a single component, reducing installation time and roof or wall penetrations.

InnoFlue® Concentric is ULC-S636 listed at zero clearance to combustibles, making it approved for use in Canada.

Concentric Vent Lengths and fittings are joined using high performance EPDM H1 gaskets which are suitable for service pressures up to 20 inches of water column (5000Pa) and are resistant to corrosive condensate.

InnoFlue® Concentric is used to vent individual appliances. InnoFlue® Concentric can be combined with InnoFlue® Single Wall and InnoFlue® Flex. For more information on system configurations, visit the InnoFlue® Concentric Solutions page.

Dimensions

  • Diameters: 2/4″ (60/100mm), 3/5″ (80/125mm), 4/6″ (110/160mm)
  • Concentric Vent Lengths (Effective Lengths): 1′, 2′ & 3′
Technical sheet

Flex

Chimneys

InnoFlue® Flex uses industry leading, flame retardant polypropylene technology to construct single wall, gasketed, flexible vent pipes and accessories. InnoFlue® Flex’s dynamic product line provides superior corrosion protection throughout. Lightweight polypropylene eliminates installation fatigue associated with most common venting materials, making it easy. The flexible properties of the Vent Length allow for the rapid lining of chimneys with offsets up to 45°. InnoFlue® is ULC-S636 listed at zero clearance to combustibles, making it approved for use in Canada.

Flexible Vent Lengths and fittings are joined using high performance EPDM H1 gaskets which are suitable for service pressures up to 20 inches of water column (5000Pa) and are resistant to corrosive condensate. 3″ and 4″ diameter Flex Vent Lengths have rigid sections every 2 feet. These rigid male sections can be inserted into any InnoFlue® Single Wall socket and allow for the easy transition between Single Wall and Flex. Once Centrocerin (installation lubricant) has dried the gaskets provide firm junctions between components.

InnoFlue® Flex is used to vent individual appliances. InnoFlue® Flex is commonly combined with InnoFlue® Single Wall but can also be combined with InnoFlue® Concentric. For more information on system configurations, visit the InnoFlue® Flex Solutions page.

Dimensions

Diameters: 2″ (60mm), 3″ (80mm), 4″ (110mm)

Available Lengths:

2″ Diameter

150′ Continuous Length
25′ Kit
35′ Kit
Custom Cut to Order

3″ Diameter

150′ Continuous Length
25′ Kit
35′ Kit
Custom Cut to Order

4″ Diameter

80′ Continuous Length
25′ Kit
35′ Kit
Custom Cut to Order

Technical sheet

Single Wall

Chimneys

InnoFlue® Single Wall Residential uses industry leading, flame retardant, polypropylene technology to construct single wall, gasketed, rigid vent pipes, fittings and accessories. InnoFlue® Single Wall’s dynamic product line provides superior corrosion protection throughout. Lightweight polypropylene eliminates installation fatigue associated with overhead installations of most common venting materials. InnoFlue® is ULC-S636 listed at zero clearance to combustibles, making it approved for use in Canada.

Vent Lengths and fittings are joined using high performance EPDM H1 gaskets, which are suitable for service pressures up to 20 inches of water column (5000Pa) and are resistant to corrosive condensate. Once Centrocerin (installation lubricant) has dried the gaskets provide firm junctions between components.

InnoFlue® Single Wall Residential can be configured to vent individual appliances or cascaded to form a common vent system. InnoFlue® Single Wall Residential can be combined with InnoFlue® Flex or InnoFlue® Concentric.

  • Diameters: 2″ (60mm), 3″ (80mm), 4″ (110mm) & 5″ (125mm)
  • Vent Lengths (Effective Lengths): 12″, 24″ 36″ & 72″
Technical sheet

Squire

Water heater

Hydronic buffer tanks are utilized to provide thermal storage volume when the system demand is less than the lowest firing rate of the boiler. This occurs most often when there are “micro” zones in the distribution system whose demand is below the minimum firing rate of the boiler. Under these conditions the boiler fires at its minimum rate, which is more energy than can be absorbed by the distribution system, and shuts off because of high return temperatures before the “micro” zone’s call for heat is satisfied. The boiler system continues to receive a call for heat and fires again. The “micro” zone cannot absorb all the energy produced by the boiler, and again the boiler shuts off because of high return temperatures. With the volume provided by the tank the additional energy not utilized by the “micro” zone can be stored in the buffer tank and used when there are additional heating demands

  • capacities from 30-120 gallons
  • 5 year limited warranty
see supplier page

Knight

Boilers

What is modulation? Let’s say your home is heated by a KNIGHT with 285,000 Btu/hr heating power. When it’s just “pretty cold” outside, the boiler starts by firing at a fuel-saving 57,000 Btu/hr, only 20% of its maximum heating potential. As the temperature drops to “really really cold,” KNIGHT is designed to “modulate” upward to the 100% maximum 285,000 Btu/hr of heating power

KNIGHT automatically adjusts its firing rate to exactly meet demand for heat.Modulation eliminates the frequent, noisy on/off cycling heard from boilers or forced-air systems that can only fire at 100%. This helps reduce wasted fuel,and ensures a (quiet KNIGHT) for your home.

see supplier page

Tank

Tank

Lochinvar’s glass lined, jacketed and insulated hot water storage tanks have been specifically engineered and constructed to provide a high volume supply of hot water at a constant outlet temperature. The unique Lock-Temp® baffle design is so effective that 80% of the storage volume can be utilized at the stored water temperature, regardless of the rate of outlet water flow

  • GLASS OR CEMENT LINED
  • ASME SECTION IV CONSTRUCTION
  • VERTICAL OR HORIZONTAL ORIENTATION
  • 125 OR 150 PSI WORKING PRESSURE
  • 5 YEAR LIMITED WARRANTY
  • Capacities from 80-5,000 Gallons
see supplier page

Industrial Boilermag XT

Filtration

Ideal for large heating systems, Boilermag XT prevents the build-up of ferrous oxide and scale in central heating systems, reducing energy bills, increasing boiler life and reducing maintenance call outs.

Utilising our high performance flow technology , Boilermag XT ensures that virtually 100% of unwanted debris is removed from the system.

  • Easy to install and maintain
  • Maintains optimum heating performance
  • Range available from 2” to 8”
  • Operating pressure up to 12 bar
  • High intensity magnetic rods capture even the smallest particles
  • Large collection capacity
  • Comes with Boilermag 3 year warranty
  • No on-going running costs
  • Premium quality manufacture

For 1½” connections see Boilermag XL

Commercial Boilermag XL

Filtration

Ideal for medium sized commercial, retail or large residential properties, Boilmermag XL prevents the build-up of ferrous oxide and scale in central heating systems, reducing energy bills and increasing boiler life.

Utilising our high performance dual flow technology , Boilermag XL ensures that virtually 100% of unwanted debris is removed from the system.

  • Easy to install and clean
  • Fits standard 1½” connections
  • Dual flow technology – filters twice on one pass
  • Guaranteed no block
  • Removes both magnetic and non-magnetic debris
  • High collection capacity
  • Comes with Boilermag 3 year warranty

For 2″-8″ connections see Boilermag XT

Boilermag

Filtration

Boilermag Domestic Heating System Filter

Our tried and trusted patented magnetic technology ensures that virtually 100% of ferrous oxide and scale is removed on first pass. This heating system filter offers major benefits:

  • Install/Clean in minutes, protects for years
  • Dual flow technology – filters twice on one pass
  • Guaranteed no block
  • Removes both magnetic and non-magnetic debris
  • Fits in line and has 360º adjustment
  • Easy access for chemical dosing
  • 22mm or 28mm available
  • High quality valves and seals

SNO-0550

Control systems

Introducing the simplest, most intuitive control available to the industry, The SN0-0550 . This standalone snow melt control replaces the SNO-0500 at the same competitive price as the previous control, but with more features and benefits. This unique control uses a new step-by-step interface allowing for easy set up. With new preset snow conditions (Very Light, Light, Moderate and Heavy), it is simple to set the control to turn on the system based on snowfall intensity.

The new snow melt control utilizes the HBX Optical Snow Sensor (SNO-0110). This snow/ice sensor utilizes optics rather than continuity based on/off sensors typically used by other manufacturers. The sensor provides HBX snow melt controls with feedback on snowfall rate and Slab Temperature.

Con X us

Control systems

From the moment you log in …

CON-X-Us technology frees you from the mechanical room. The CON-X-US application communicates over the internet via Wi-Fi or hardwire. Using any smart device, you can link up with SMART SYSTEM controls boilers in multiple locations, for multiple customers. From a single boiler to an 8-unit cascade system, you’ll be able to check operating status or re-program boiler functions,from anywhere

see supplier page

VIP

Chimneys

Chimney for gas, oil, and diesel – 6” to 48”

Waterproof envelope system

APPLICATIONS

The VIP model chimney is a prefabricated chimney made for use with forced draft and negative or neutral draft appliances, such as high-pressure steam boilers, building heating equipment, industrial furnaces, kilns, hoods, and ovens. It can also be used with diesel exhaust engines and gas turbines. The VIP model chimney was designed as a complete venting system capable of functioning in positive forced draft and negative or neutral pressure conditions. It was designed and tested for flue gas temperatures of up to 537°C (1000° F). Fire safety clearance for combustibles is dependent on your maximum operating temperature; the maximum allowable continuous flue gas temperature for the VIP chimney is 760° C (1400° F).

CONSTRUCTION

The VIP is a double wall insulated chimney. Its inner lining is equipped with a graphite pressure seal, while its outer casing uses a silicone pressure seal. To allow for a variety of applications and fuels, the VIP’s chimney flue and casing are available in several materials and thicknesses. The standard VIP chimney, which is suited to most applications, is produced with 1” of high-temperature, high-density insulation. For non-standard custom applications, the VIP model is available with either 2” or 4” of insulation. We recommend using stainless steel chimney lengths for all corrosive or exterior environments.

Technical sheet

VIC

Chimneys

VIC – Condensing vent

APPLICATIONS :

ICC’s VIC model is a single wall, double wall, or insulated double wall vent system used for condensing and near-condensing appliances. It is tested and listed to UL 1738/ULC S636 standards. The VIC condensing vent can be used for the applications below:

  • Category I, II, III, and IV gas appliances with a maximum flue gas temperature of 550° F.
  • BH-type gas vents for appliances with a maximum flue gas temperature of 550° F.
  • Appliances that produce condensation in the exhaust stream.
CONSTRUCTION:

The VIC model’s inner liner is built from super-ferritic AL294C-type stainless steel or 444-type stainless steel; both alloys meet the requirements for the UL corrosion resistance test. The exterior wall of the double wall VIC system is made using 430-type stainless steel. The VIC model is offered in the following configurations:

  • Single wall: used to connect different appliances together. This system is lightweight and easy to install horizontally. It is recommended to install the VIC single wall vent inside the building or in an environment where the temperature remains above freezing.
  • Double wall: the double wall improves heat retention inside the flue, which increases draft strength and can reduce safety clearance to combustibles in some cases. The double wall model also has a lower impact on ambient temperature (in a mechanical room, for example). It is approved for both interior and exterior installations.
  • Double wall insulated: this model is the best choice for exterior installations in cold climates. The insulated exterior casing minimizes heat loss and increases draft strength. This model’s inner liner, which measures between 5” and 16” in diameter, is either tungsten arc welded or laser welded – both butt welding techniques. Butt welding lessens the impact on the steel and creates a smooth and corrosion-resistant seam.
Technical sheet

Concentrique

Chimneys

Matériaux et construction

InnoFlue® Concentric intègre le chef de file de l’industrie l’InnoFlue® Single Wall, une technologie de polypropylène ignifugé et de gaines métalliques revêtues à la poudre en blanc. Ce système intégré permet aux gaz d’échappement et à l’air frais de circuler dans un seul composant ainsi que de réduire la pénétration du plafond et des murs et le temps d’installation.

InnoFlue® Concentric est sur la liste ULC-S636 à aucun dégagement de combustibles, grâce à quoi il est autorisé au Canada.

Les longueurs et les raccords des évents Concentric sont reliés par des joints d’étanchéités EPDM H1 de haute performance convenant à une pression de service allant jusqu’à 20 pouces de colonne d’eau (5 000 Pa) et sont résistants au condensat corrosif.

InnoFlue® Concentric est utilisé pour aérer les appareils individuels. InnoFlue® Concentric peut être combiné à InnoFlue® Single Wall et InnoFlue® Flex.  Pour de
plus ambles informations à propos des configurations de système, visitez la page d’InnoFlue® Concentric Solutions.

Dimensions :

  • Diamètres : 2/4″ (60/100mm), 3/5″ (80/125mm), 4/6″ (110/160mm)
  • Longueurs d’évents Concentric (longueurs effectives) : 1′, 2′ et 3′
Technical sheet

Flex

Chimneys

InnoFlue® Flex uses industry leading, flame retardant polypropylene technology to construct single wall, gasketed, flexible vent pipes and accessories. InnoFlue® Flex’s dynamic product line provides superior corrosion protection throughout. Lightweight polypropylene eliminates installation fatigue associated with most common venting materials, making it easy. The flexible properties of the Vent Length allow for the rapid lining of chimneys with offsets up to 45°. InnoFlue® is ULC-S636 listed at zero clearance to combustibles, making it approved for use in Canada.

Flexible Vent Lengths and fittings are joined using high performance EPDM H1 gaskets which are suitable for service pressures up to 20 inches of water column (5000Pa) and are resistant to corrosive condensate. 3″ and 4″ diameter Flex Vent Lengths have rigid sections every 2 feet. These rigid male sections can be inserted into any InnoFlue® Single Wall socket and allow for the easy transition between Single Wall and Flex. Once Centrocerin (installation lubricant) has dried the gaskets provide firm junctions between components.

InnoFlue® Flex is used to vent individual appliances. InnoFlue® Flex is commonly combined with InnoFlue® Single Wall but can also be combined with InnoFlue® Concentric. For more information on system configurations, visit the InnoFlue® Flex Solutions page.

Dimensions

Diameters: 2″ (60mm), 3″ (80mm), 4″ (110mm)

Available Lengths:

2″ Diameter

150′ Continuous Length
25′ Kit
35′ Kit
Custom Cut to Order

3″ Diameter

150′ Continuous Length
25′ Kit
35′ Kit
Custom Cut to Order

4″ Diameter

80′ Continuous Length
25′ Kit
35′ Kit
Custom Cut to Order

Technical sheet

Single Wall

Chimneys

InnoFlue® Single Wall Residential uses industry leading, flame retardant, polypropylene technology to construct single wall, gasketed, rigid vent pipes, fittings and accessories. InnoFlue® Single Wall’s dynamic product line provides superior corrosion protection throughout. Lightweight polypropylene eliminates installation fatigue associated with overhead installations of most common venting materials. InnoFlue® is ULC-S636 listed at zero clearance to combustibles, making it approved for use in Canada.

Vent Lengths and fittings are joined using high performance EPDM H1 gaskets, which are suitable for service pressures up to 20 inches of water column (5000Pa) and are resistant to corrosive condensate. Once Centrocerin (installation lubricant) has dried the gaskets provide firm junctions between components.

InnoFlue® Single Wall Residential can be configured to vent individual appliances or cascaded to form a common vent system. InnoFlue® Single Wall Residential can be combined with InnoFlue® Flex or InnoFlue® Concentric.

  • Diameters: 2″ (60mm), 3″ (80mm), 4″ (110mm) & 5″ (125mm)
  • Vent Lengths (Effective Lengths): 12″, 24″ 36″ & 72″
Technical sheet

Squire

Water heater

Hydronic buffer tanks are utilized to provide thermal storage volume when the system demand is less than the lowest firing rate of the boiler. This occurs most often when there are “micro” zones in the distribution system whose demand is below the minimum firing rate of the boiler. Under these conditions the boiler fires at its minimum rate, which is more energy than can be absorbed by the distribution system, and shuts off because of high return temperatures before the “micro” zone’s call for heat is satisfied. The boiler system continues to receive a call for heat and fires again. The “micro” zone cannot absorb all the energy produced by the boiler, and again the boiler shuts off because of high return temperatures. With the volume provided by the tank the additional energy not utilized by the “micro” zone can be stored in the buffer tank and used when there are additional heating demands

  • capacities from 30-120 gallons
  • 5 year limited warranty
see supplier page

Shield

Water heater

The Shield™ commercial water heater features an advanced water heating system beautifully packaged for the smallest possible footprint. The Shield is available in eight models in standard and ASME construction. All utility connections are located at the top of the appliance to reduce equipment room footprint and increase installation flexibility. The Smart Control™ offers a bright, clear LCD display with soft-key buttons and a wide variety of advanced control functions. Additionally, a large removable pump access panel as well as the control can be found in the front of the cabinet making serviceability a snap

  • EIGHT MODELS FROM
  • 125,000 TO 500,000 BTU/HR
  • NO EFFICIENCY LOSS FROM LIME SCALE
  • VIRTUALLY SILENT OPERATION
  • ADVANCED SMART CONTROL™
see supplier page

ArmorX2

Water heater

The ARMOR X2 Commercial Water Heater combines stainless steel heat exchanger technology with Modulating Condensing combustion to deliver efficiencies as high as 96%. With models at 1.0, 1.3 and 1.5 million BTU/hr inputs, ARMOR X2 will serve a large range of commercial applications and add the “green” touch that building owners and facility managers desire.ARMOR X2 delivers new levels of innovation with SMART TOUCH… touchscreen technology that puts total operational control at your fingertips! With Lochinvar SMART TOUCH, it’s easier than ever to set up a perfectly synchronized “green” system, and access a complete onboard database of real-time operational data and performance history. Other features of the ARMOR X2 include space-saving footprints, direct-vent design with intake and exhaust runs up to 100 equivalent feet, and a built-in cascading sequencer for up to 8 water heaters, delivering up to 12 million BTU/hr capacity

see supplier page

Armor

Water heater

ARMOR is a fully condensing commercial gas water heater. Available in eight models with inputs ranging from
150,000 to 800,000 Btu/hr, the ARMOR achieves thermal efficiencies up to 96%.

With standard tank-type water heaters, your choices are limited when it comes to matching input with storage capacity to meet “peak demand” delivery requirements. With ARMOR, you can match one or more water heaters with inputs ranging from 150,000 to 800,000 with one or more storage tanks in a wide variety of sizes. Lochinvar Lock-Temp® tanks are available to meet the need, from our 80-gallon vertical to the 5000-gallon vertical or horizontal model.

Another advantage of the ARMOR “dual component” system is lower replacement costs. Standard tank-type designs require replacement of the entire water heater. With ARMOR, you’ll save time and money by only replacing individual components as needed, such as the pump or storage tank

see supplier page

Knight XL

Boilers

The KNIGHT® XL, engineered with Lochinvar’s exclusive SMART SYSTEM™ control and an array of other innovative features, places it far ahead of any commercial heating boiler in its class. It promises and delivers ultimate ease of installation and maintenance. With up to 94.6% thermal efficiency, low-NOx emissions and a fully modulating burner, it is the best ”green choice” for today’s environmentally focused market.Five modulating/condensing stainless steel KNIGHT XL boilers are available with 399,000–800,000 Btu/hr inputs and remarkably small space-saving footprints. All are equipped for direct-vent installation with air intake and exhaust runs up to 100 feet using PVC, CPVC, Polypropylene or AL29-4C vent materials. This range of choices is ideal for light-duty applications such as small hotels, schools and office buildings. For higher-demand applications, up to eight KNIGHT XL units can be installed utilizing the built-in cascading sequencer to deliver up to 6.4 million Btu/hr heating capacity.THE KNIGHT XL BOILER reflects Lochinvar’s constant commitment to providing all the options you need to serve every application

see supplier page

Knight

Boilers

What is modulation? Let’s say your home is heated by a KNIGHT with 285,000 Btu/hr heating power. When it’s just “pretty cold” outside, the boiler starts by firing at a fuel-saving 57,000 Btu/hr, only 20% of its maximum heating potential. As the temperature drops to “really really cold,” KNIGHT is designed to “modulate” upward to the 100% maximum 285,000 Btu/hr of heating power

KNIGHT automatically adjusts its firing rate to exactly meet demand for heat.Modulation eliminates the frequent, noisy on/off cycling heard from boilers or forced-air systems that can only fire at 100%. This helps reduce wasted fuel,and ensures a (quiet KNIGHT) for your home.

see supplier page

FTXL

Boilers

Lochinvar re-defined the fire-tube boiler category with its KNIGHT Wall-Mount and CREST lines. For residential and light commercial applications, the FTXL™ adds models from 399,999 to 850,000 Btu/hr, and takes Lochinvar’s fire-tube technology to the next level. FTXL offers best-in-class AHRI Thermal Efficiency and footprints, plus remote connectivity that puts the SMART SYSTEM control at your fingertips, anywhere!

see supplier page

Crest

Boilers

Lochinvar ®has taken the fire-tube concept in an innovative new direction with the CREST modulating-condensing boiler. With sizes that range from 2.5 to 5.0 million Btu/hr, you have the opportunity to utilize Lochinvar leading-edge technology in your largest applications. With thermal efficiencies up to 99% in low water temperature applications,CREST is positioned to provide exceptional energy-saving performance.

The advanced CREST introduces a combustion system with a unique burner design with up to 20:1 turndown. The burner fires into an array of 316L stainless steel fire-tubes that transfer the heat to the surrounding water with exceptionally high efficiency.

CREST communicates seamlessly and in real time with building management systems by utilizing an on-board MODBUS protocol. The SMART TOUCH™ control has a built-in cascading component that communicates with up to eight units, providing total command without an external control or complex and expensive control logic programming by the BMS integrator. Yes, innovative fire-tube boiler technology integrated with our SMART TOUCH™ operating control makes the CREST a genuine game-changer among commercial boilers

see supplier page